- #Playboy runabout boat full size#
- #Playboy runabout boat manual#
- #Playboy runabout boat trial#
- #Playboy runabout boat free#
Here the hull has been coated with epoxy and primed. Sanding the epoxy essentially completed the planking!! Here we see the transom tumblehome and "non-trip chines."Īlthough the plywood has not yet been trimmed along the gunwales, Three rachet straps were needed to pull the aft side planking into shape at the transom.Īll of the screw heads were filled with epoxy fairing compound. With 1/8" strips of wood to make sure everything fit correctly. Paul checked the fairing of the bilge battens with a strip of 1/4" plywood as a batten.Ī cardboard pattern was used to fit the forward bottom plywood.ģ/8" Philippine mahogany marine plywood was used on the bottom.ġ/4" Mahogany plywood was used on the chines after packing the frames, transom and chines Paul's neighbor takes a look at the completed frame. Paul laminated them from two pieces of stock needing almost 50 clamps! It's tougher to get good lumber now than it was in the 50s and 60s. When the chines were installed the first time, they broke at the #1 frame when left overnight. The #2 frame was also modified from the original plans but the bottom contours were kept as original. You can see were he modified the bottom framing, adding two more bilge battens on each side.
He found that the transom knees did not align properly and had to be adjusted. Everything fit after a little adjustment.Īfter all the frames were glued up and a major pieces were cut out, Paul clamped everything together to see how it fit.
#Playboy runabout boat trial#
Here's the trial fit of the forward frame, rim pieces and stem.
#Playboy runabout boat full size#
He laid out the frames full size using a roll of brown building paper and a lofting table made from two sheets of plywood. Paul cut some trial framing from pine boards to see how everything would fit together. Due to the change in lumber sizes over the years (a 2x is no longer 1-5/8" thick nor is a 4x 3-5/8"), adjustments were necessary in stringer sizes.
Paul drew the plans full size in his basement and started construction. This was what he was looking for plywood on frame construction, not too big, not many frames, not overly complicated, and it was similar to the type of boat his family had owned in his youth. Jackson's Ace plans from a 1956 Handbook are available. He looked at a few old copies of the Boat Builder's Handbook and then found Svenson's web site where William D. For additional information, we recommend the iboats forums and a boating safety course.Paul Gager of New Jersey had already built an 8-foot dinghy and a 16-foot sailboat. Information here to make sure it matches up with your boat. Thus, for safety and other reasons, it is a good idea to verify Because this information has come from many sources we can not guarantee its accuracy.Įven if this information is the same as the original factory specs, boats are sometimes modified.
#Playboy runabout boat free#
Information on this page is provided to you as a free service of. Applicable engine information has been included below since a boat needs reliable power. Good maintenance and care can help your vessel stay in good condition and have a higher value at resale. While this runabout does have a hull made of fiberglass, it is beneficial to keep the boat clean and dry by covering it properly while not in use. When repowering, it is best to verify this information for the sake of safety and to ensure that your insurance company will cover you.
#Playboy runabout boat manual#
If you do not have the manual for your engine then we highly recommend that you get one as repowering is costly and it takes you off of the water. The max rated horsepower of this boat, as listed by the manufacturer, (according to records we have) is 250 hp. which does not include passengers, aftermarket boating accessories, or fuel. The 1976, Playboy 24 is a 23.75 foot outboard boat.
0 kommentar(er)
